India

Welcome to the Schneider Electric Website

Welcome to our website.

You can choose another country to view available products or go to our Global website for company information.

Choose another country or region

ATV71LD10N4Z Product picture Schneider Electric

View all Altivar Lift

Altivar Lift - ATV71LD10N4Z

Variable speed drives

ATV71LD10N4Z Product picture Schneider Electric
View all Altivar Lift
Altivar Lift - ATV71LD10N4Z
Variable speed drives

variable speed drive ATVLift - 4 kW 5 Hp - 480 V - EMC filter - with heat sink

Show more characteristics >
Add to My Products Remove from My Products

  • Main
    range of product
    Altivar Lift
    product or component type
    Variable speed drive
    device short name
    ATV71
    product destination
    Asynchronous motors
    Synchronous motors
    product specific application
    Lift
    assembly style
    With heat sink
    variant
    With integrated 7-segment display terminal
    EMC filter
    Integrated
    network number of phases
    3 phases
    [Us] rated supply voltage
    380...480 V (- 15...10 %)
    supply voltage limits
    323...528 V
    supply frequency
    50...60 Hz (- 5...5 %)
    network frequency
    47.5...63 Hz
    motor power kW
    3 phases
    motor power hp
    3 phases
    line current
    14.1 A for 380 V, 3 phases / 4 kW / 5 hp
    11.5 A for 480 V, 3 phases / 4 kW / 5 hp
    Complementary
    apparent power
    9.3 kVA for 380 V, 3 phases / 4 kW / 5 hp
    prospective line Isc
    <= 5 kA, 3 phases
    nominal output current
    10.5 A at 4 kHz, 380 V 3 phases / 4 kW / 5 hp
    7.6 A at 4 kHz, 460 V 3 phases / 4 kW / 5 hp
    maximum transient current
    14.3 A for 2 s 3 phases / 4 kW / 5 hp
    speed drive output frequency
    0...599 Hz
    braking resistance
    >= 19 Ohm
    nominal switching frequency
    8 kHz
    switching frequency
    1...16 kHz adjustable
    speed range
    1...100 asynchronous motor in open-loop mode, without speed feedback
    1...50 synchronous motor in open-loop mode, without speed feedback
    1...1000 asynchronous motor in closed-loop mode with encoder feedback
    speed accuracy
    +/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation, in closed-loop mode with encoder feedback
    +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation, without speed feedback
    torque accuracy
    +/- 15 % in open-loop mode, without speed feedback
    +/- 5 % in closed-loop mode with encoder feedback
    transient overtorque
    170 %, +/- 10 % for 60 s
    220 %, +/- 10 % for 2 s
    braking torque
    <= 150 % with braking or hoist resistor
    30 % without braking resistor
    asynchronous motor control profile
    Voltage/frequency ratio, 2 points
    Voltage/frequency ratio, 5 points
    Flux vector control without sensor, standard
    Voltage/frequency ratio - Energy Saving, quadratic U/f
    Flux vector control without sensor, ENA (energy Adaptation) system
    Flux vector control without sensor, 2 points
    Flux vector control with sensor, standard
    synchronous motor control profile
    Vector control without sensor, standard
    Vector control with sensor, standard
    regulation loop
    Adjustable PI regulator
    motor slip compensation
    Adjustable
    Automatic whatever the load
    Not available in voltage/frequency ratio (2 or 5 points)
    Suppressable
    local signalling
    1 LED - red - drive voltage
    output voltage
    <= power supply voltage
    insulation
    Electrical between power and control
    type of cable for external connection
    IEC cable without mounting kit : 1 wire(s) - 45 °C, copper 90 °C / XLPE/EPR
    IEC cable without mounting kit : 1 wire(s) - 45 °C, copper 70 °C / PVC
    IEC cable with an IP21 or an IP31 kit : 3 wire(s) - 40 °C, copper 70 °C / PVC
    UL 508 cable with a NEMA Type1 kit : 3 wire(s) - 40 °C, copper 75 °C / PVC
    electrical connection
    Terminal 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
    Terminal 4 mm² / AWG 10 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
    tightening torque
    0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
    1.4 N.m - 12.3 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
    supply
    Internal supply for reference potentiometer (1 to 10 kOhm) at 10.5 V DC +/- 5 % - <= 10 A with overload and short-circuit protection
    Internal supply at 24 V DC (21...27 V) - <= 200 A with overload and short-circuit protection
    analogue input number
    2
    analogue input type
    Software-configurable current : (AI2) 0...20 mA - 242 Ohm - resolution: 11 bits
    Software-configurable voltage : (AI2) 0...10 V DC - 24 V max - 30000 Ohm - resolution: 11 bits
    Bipolar differential voltage : (AI1-/Al1+) +/- 10 V DC - 24 V max - resolution: 11 bits + sign
    sampling duration
    2 ms +/- 0.5 ms (LI6) if configured as logic input - discrete input(s)
    2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s)
    2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s)
    2 ms +/- 0.5 ms (Al2) - analog input(s)
    response time
    <= 100 ms in STO (Safe Torque Off)
    7 ms +/- 0.5 ms (R1A, R1B, R1C) - discrete output(s)
    7 ms +/- 0.5 ms (R2A, R2B) - discrete output(s)
    2 ms +/- 0.5 ms (AO1) - analog output(s)
    accuracy
    +/- 1 % (AO1) for a temperature variation 60 °C
    +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
    +/- 0.6 % (AI2) for a temperature variation 60 °C
    linearity error
    +/- 0.15 % of maximum value (AI1-/Al1+, AI2)
    +/- 0.2 % (AO1)
    analogue output number
    1
    analogue output type
    Software-configurable current : (AO1) 0...20 mA - 500 Ohm - resolution: 10 bits
    Software-configurable voltage : (AO1) 0...10 V DC - 470 Ohm - resolution: 10 bits
    Software-configurable logic output : (AO1) 10 V - <= 20 A
    discrete output number
    2
    discrete output type
    Configurable relay logic : (R1A, R1B, R1C) NO/NC - 100000 cycles
    Configurable relay logic : (R2A, R2B) NO - 100000 cycles
    minimum switching current
    3 mA at 24 V DC (configurable relay logic)
    maximum switching current
    5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2)
    5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2)
    2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2)
    2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2)
    discrete input number
    7
    discrete input type
    Switch-configurable PTC probe (LI6) - 0...6 probes - 1500 Ohm
    Programmable (LI1...LI5) 24 V DC, with level 1 PLC - 3500 Ohm
    Switch-configurable (LI6) 24 V DC, with level 1 PLC - 3500 Ohm
    Safety input (PWR) 24 V DC - 1500 Ohm
    discrete input logic
    Negative logic (LI6) if configured as logic input, > 16 V (state 0), < 10 V (state 1)
    Positive logic (LI6) if configured as logic input, < 5 V (state 0), > 11 V (state 1)
    Positive logic (LI1...LI5), < 5 V (state 0), > 11 V (state 1)
    Negative logic (LI1...LI5), > 16 V (state 0), < 10 V (state 1)
    Positive logic (PWR), < 2 V (state 0), > 17 V (state 1)
    acceleration and deceleration ramps
    Automatic adaptation of ramp if braking capacity exceeded, by using resistor
    Linear adjustable separately from 0.01 to 9000 s
    S, U or customized
    protection type
    Overheating protection for drive
    Thermal protection for drive
    Short-circuit between motor phases for drive
    Overcurrent between output phases and earth for drive
    Overvoltages on the DC bus for drive
    Break on the control circuit for drive
    Against exceeding limit speed for drive
    Line supply undervoltage for drive
    Line supply overvoltage for drive
    Against input phase loss for drive
    Thermal protection for motor
    Motor phase break for motor
    Input phase breaks for drive
    Power removal for motor
    dielectric strength
    3535 V DC between earth and power terminals
    5092 V DC between control and power terminals
    insulation resistance
    > 1 mOhm at 500 V DC for 1 minute to earth
    frequency resolution
    0.1 Hz for display unit
    0.024/50 Hz for analog input
    communication port protocol
    CANopen
    Modbus
    connector type
    1 RJ45 for Modbus on front face
    1 RJ45 for Modbus on terminal
    Male SUB-D 9 on RJ45 for CANopen
    physical interface
    2-wire RS 485 for Modbus
    transmission frame
    RTU for Modbus
    transmission rate
    20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
    4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
    9600 bps, 19200 bps for Modbus on front face
    data format
    8 bits, 1 stop, even parity for Modbus on front face
    8 bits, odd even or no configurable parity for Modbus on terminal
    type of polarization
    No impedance for Modbus
    number of addresses
    1...247 addresses for Modbus
    1...127 addresses for CANopen
    method of access
    Slave for CANopen
    control options
    Controller inside programmable card
    I/O extension card
    Interface card for encoder
    Overhead crane card
    Communication card for Profibus DP
    Communication card for Modbus TCP
    Communication card for Fipio
    Communication card for Modbus/Uni-Telway
    Communication card for Modbus Plus
    Communication card for Ethernet/IP
    Communication card for DeviceNet
    Communication card for Profibus DP V1
    Communication card for Interbus-S
    Communication card for CC-Link
    operating position
    Vertical +/- 10 degree
    Environment
    electromagnetic compatibility
    1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
    Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
    Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
    Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
    Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
    Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
    pollution degree
    2 conforming to EN/IEC 61800-5-1
    IP degree of protection
    IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529
    IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1
    IP21 conforming to EN/IEC 60529
    IP21 conforming to EN/IEC 61800-5-1
    IP41 on upper part conforming to EN/IEC 60529
    IP41 on upper part conforming to EN/IEC 61800-5-1
    IP54 on lower part conforming to EN/IEC 60529
    IP54 on lower part conforming to EN/IEC 61800-5-1
    vibration resistance
    1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
    1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
    shock resistance
    15 gn for 11 ms conforming to EN/IEC 60068-2-27
    noise level
    54.5 dB conforming to 86/188/EEC
    relative humidity
    5...95 % without condensation conforming to IEC 60068-2-3
    5...95 % without dripping water conforming to IEC 60068-2-3
    ambient air temperature for operation
    -10...50 °C without derating
    ambient air temperature for storage
    -25...70 °C
    operating altitude
    <= 1000 m without derating
    1000...3000 m with current derating 1 % per 100 m
    standards
    EN 55011 class A group 1
    EN 61800-3 environments 1 category C2
    EN 61800-3 environments 2 category C2
    EN/IEC 61800-3
    EN/IEC 61800-5-1
    IEC 60721-3-3 class 3C1
    IEC 60721-3-3 class 3S2
    UL Type 1
    product certifications
    CSA
    C-Tick
    GOST
    NOM 117
    UL
    marking
    CE
    Offer Sustainability
    Sustainable offer status
    Green Premium product
    RoHS (date code: YYWW)
    REACh
    Product environmental profile
    Available
    Product end of life instructions
    Available
    Contractual warranty
    Warranty period
    18 months
  • Documents & Downloads

    Language
    • English
    DTM files
    Date
    Size
    Add to My Documents
    Altivar DTM Library V12.8: ATV12, ATV31/312, ATV32, ATV61, ATV71, ATV LIFT, ATV212 (Version 12.8)
    Catalogue
    Date
    Size
    Add to My Documents
    Catalog: Altivar 71/71 Plus variable speed drives - English version 2014/04 (web pdf format) (Version 1.0)
    User guide
    Date
    Size
    Add to My Documents
    ATV71 Installation Manual 0,37 - 90 kW (Version 05)
    ATV LIFT communication parameters V5.4 (Version 03)
    ATV LIFT programming manual (Version 04)
    Date 13/12/18
    Size 3.5 MB
    ATV LIFT Quick start guide (Version 01)
    Date 13/12/18
    Size 527.9 KB
    ATV61/71/ LIFT Safety integrated function manual (Version 04)
    Certificate
    Date
    Size
    Add to My Documents
    ATV71L_EU_DECLARATION (Version 1.0)
    Date 23/5/18
    Size 546.8 KB
    Instruction sheet
    Date
    Size
    Add to My Documents
    Instruction sheet - Ferrite core (Version 01)
    Date 13/12/17
    Size 283.1 KB
    Instruction Sheet - migration table ATV71L to ATV LIFT (Version 02)
    EDS files
    Date
    Size
    Add to My Documents
    ATV_LIFT_DeviceNet (Version 5.4)
    Date 31/1/19
    Size 1.3 MB
    Date 31/1/19
    Size 393 B
    Date 31/1/19
    Size 3.7 KB
    ATV LIFT CANopen files (Version 5.4)
    Date 31/1/19
    Size 484 B
    Date 31/1/19
    Size 165.9 KB
    Date 31/1/19
    Size 4.6 KB
    Date 31/1/19
    Size 4.6 KB
    Date 31/1/19
    Size 4.6 KB
    REACh Declaration
    Date
    Size
    Add to My Documents
    EU RoHS Declaration
    Date
    Size
    Add to My Documents
  • Technical FAQs

    No results found.
    Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.